Lenovo BladeCenter HX5 1909 Problem Determination And Service Manual Download Page 213

Page: 213 / 313

• Follow the suggested actions in the order in which they are listed in the Action column until the problem is

solved.

• See “

Parts listing - BladeCenter HX5

” on page 57 to determine which components are CRUs and which

components are FRUs.

• If an action step is preceded by “(Trained service technician only),” that step must be performed only by a

trained service technician.

Type

Error Message

Action

Error

Expansion Module

, (BPE4_

Slot

)

PCI system error

Notes:

= Module number

= BPE4 ID (1, 2, 3, or 4). The

max BPE4 number is 4, and
there are 2 slots in each BPE4.
Module number is based on the
configuration of the BPE4

1. If you have a PCI adapter in your blade server, verify that

the PCI adapter is supported in the blade server. For a list
of supported optional devices for the blade server, see
http://www.ibm.com/servers/eserver/serverproven/
compat/us/.

2. Reseat the PCI adapter (see “Removing an I/O expansion

card” on page 119 and “Installing an I/O expansion card”
on page 121).

Error Code: 0x806F052B

Error

System mgmt software, (IMM FW
Failover) unsupported software
version

This error occurs when the service processor (IMM) firmware is
corrupted and has reverted to a previous version of the
firmware.

Complete the following steps to correct this error:

1. Check the IBM support website for an applicable firmware

update that applies to the blade server.

2. Restart the IMM and verify the IMM is running the correct

firmware level after the firmware update.

For more information about updating the firmware and the
preferred methods, see

Firmware Update Best Practices

http://www-947.ibm.com/support/entry/portal/docdisplay?
brand=5000020&lndocid=MIGR-5082923.

Error Code: 0x806F0607

Note:

Multiple events can be displayed for this error code. Be sure to read the message text to determine the

appropriate recovery actions.

Error

Group 4, processor (One of CPUs)
SM BIOS uncorrectable error

1. Verify that the latest system firmware is installed (see

“Updating firmware and device drivers” on page 30).

2. (Trained service technician only) Replace the

microprocessors one at a time (see “Removing a
microprocessor and heat sink” on page 130 and
“Removing a microprocessor and heat sink” on page 130).

3. (Trained service technician only) Replace the system-

board assembly (see “Removing the system-board
assembly - BladeCenter HX5” on page 140 and “Installing
the system-board assembly - BladeCenter HX5” on page
142).

Chapter 5

Diagnostics

197

Summary of Contents for BladeCenter HX5 1909


























































































































































































































































































































Search results

Summary of Contents for BladeCenter HX5 1909

Reviews:

Related manuals for BladeCenter HX5 1909

Brands by name

Popular brands

Lenovo BladeCenter HX5 1909, Problem Determination And Service Manual

Search results

Summary of Contents for BladeCenter HX5 1909

Reviews:

Related manuals for BladeCenter HX5 1909

Brands by name

Popular brands