Lenovo BladeCenter HX5 1909 Problem Determination And Service Manual Download Page 90

Page: 90 / 313

Removing an expansion unit

Use these instructions to remove an expansion unit from a blade server or from the topmost blade server in a
scalable blade complex.

Blade server
cover release

Cover
Pins

To open and remove an expansion unit, complete the following steps.

Step 1. Before you begin, read “Safety” on page v and “Installation guidelines” on page 65.

Step 2. If the blade server or scalable blade complex is installed in a BladeCenter chassis, remove it. See

“Removing the blade server from the BladeCenter chassis” on page 66 for instructions.

Step 3. Carefully lay the blade server on a flat, static-protective surface, orienting the blade server with the

bezel pointing toward you.

Step 4. Open the blade server cover (see “Removing the blade server cover” on page 71 for instructions).

Step 5. Press the blade server cover release on each side of the blade server and lift the expansion unit

from the blade server.

Step 6. Rotate the expansion blade open; then, lift the expansion blade from the blade server.

Step 7. If additional expansion units need to be removed, repeat steps Step 5 on page 74 and Step 6 on

page 74.

Step 8. If you are instructed to return the expansion unit, follow all packaging instructions, and use any

packaging materials for shipping that are supplied to you.

Important:

Do not return the blade cover. You will need to install the blade cover from the

BladeCenter HX5 on to the new expansion unit. The BladeCenter HX5 blade cover contains the
system-service label on the bottom of the cover.

Statement 12

CAUTION:
The following label indicates a hot surface nearby.

BladeCenter HX5 Blade ServerProblem Determination and Service Guide

Summary of Contents for BladeCenter HX5 1909


























































































































































































































































































































Search results

Summary of Contents for BladeCenter HX5 1909

Reviews:

Related manuals for BladeCenter HX5 1909

Brands by name

Popular brands

Lenovo BladeCenter HX5 1909, Problem Determination And Service Manual

Search results

Summary of Contents for BladeCenter HX5 1909

Reviews:

Related manuals for BladeCenter HX5 1909

Brands by name

Popular brands