Lenovo BladeCenter HX5 1909 Problem Determination And Service Manual Download Page 95

Page: 95 / 313

Step 3. Remove the cover from the topmost blade server (see “Removing the blade server cover” on page

71 for instructions).

Step 4. Stand the blade servers upright on a clean, flat work surface, with the 2-node scalability card facing

up.

Step 5. Remove the 2-node scalability card (see “Removing the 2-node scalability card” on page 83 for

instructions).

Step 6. Press the blade server cover release on each side of the blade server and lift the topmost blade

server from the bottom blade server as shown in the following illustration.

Blade server
cover release

Secondary
BladeCenter HX5
blade server

Step 7. Carefully lay the blade server on a flat, static-protective surface, with the cover side down.

Step 8. Using a small screwdriver, press down on the spring plates to disengage them.

Step 9. Pressing down firmly on the middle of the tray, slide the scalability tray back.

Chapter 4

Removing and replacing blade server components

Summary of Contents for BladeCenter HX5 1909


























































































































































































































































































































Search results

Summary of Contents for BladeCenter HX5 1909

Reviews:

Related manuals for BladeCenter HX5 1909

Brands by name

Popular brands

Lenovo BladeCenter HX5 1909, Problem Determination And Service Manual

Search results

Summary of Contents for BladeCenter HX5 1909

Reviews:

Related manuals for BladeCenter HX5 1909

Brands by name

Popular brands