Lenovo BladeCenter HX5 1909 Problem Determination And Service Manual Download Page 261 | Manualshive

Page: 261 / 313

background image

• See “

Parts listing - BladeCenter HX5

” on page 57 to determine which components are CRUs and which

components are FRUs.

• If an action step is preceded by “(Trained service technician only),” that step must be performed only by a

trained service technician.

Error code

Description

Action

215-000-xxx

Passed the optical drive self test.

215-801-xxx

Aborted the optical drive self test because it
was unable to communicate with the device
driver.

1. Make sure that the DSA code is at the latest

level, and upgrade if necessary; then, run the
test again (see “Diagnostic tools overview” on
page 146). The latest code can be found IBM
support website at http://www.ibm.com/
systems/ support/supportsite.wss/docdisplay?
brandind=5000008&lndocid=SERV-DSA.

2. Make sure that the cable for the optical drive is

securely connected at both ends of the cable,
then; tighten any loose connections. See your
BladeCenter documentation for information
about replacing the optical drive (media tray).

3. Make sure that the cable for the optical drive is

not damaged, then; replace the cable if damage
is present. See your BladeCenter
documentation for information about replacing
the optical drive.

4. Run the test again. See “Diagnostic tools

overview” on page 146.

5. For additional troubleshooting information, go to

http://www.ibm.com/support/docview.wss?
uid=psg1MIGR-41559.

6. Make sure that the system firmware level is at

the latest level and upgrade if necessary; then,
run the test again. The installed firmware level
can be found in the DSA log within the
Firmware/VPD section for this component. The
latest level firmware for this component can be
found on the IBM support website at http://
www.ibm.com/support/ fixcentral/systemx/
groupView? query.productGroup=ibm%
2FBladeCenter.

7. Run the test again. See “Diagnostic tools

overview” on page 146.

8. Replace the CD or DVD drive. See your

BladeCenter chassis documentation for
information about replacing the optical drive
(media tray).

9. Collect the data from the DSA event log and

send it to IBM Service. For information about
contacting and sending data to IBM Service, go
to Appendix A “Getting help and technical
assistance” on page 277.

245

«
...
259
260
261
262
263
...
»

Summary of Contents for BladeCenter HX5 1909


























































































































































































































































































































Reviews:

No comments

Related manuals for BladeCenter HX5 1909

Brand: Panasonic Pages: 16

Brand: Lantronix Pages: 299

Brand: Omneon Pages: 2

Brand: Bang & Olufsen Pages: 28

Silex Pricom SX-2000U2

Brand: Silex technology Pages: 1

419452u - Servers System X3250 M2 Xeon...

Brand: IBM Pages: 84

Brand: TYAN Pages: 81

DIGI CONNECT ES

Brand: Digi Pages: 23

Brand: Synology Pages: 16

Brand: Synology Pages: 33

Brand: Synology Pages: 20

Brand: Synology Pages: 21

DiskStation DS411

Brand: Synology Pages: 22

InterServe 80 SL

Brand: Intergraph Pages: 106

Brand: EVS Pages: 126

Brand: EVS Pages: 118

Brand: Bosanova Pages: 2

Brand: Sierra Wireless Pages: 53

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands