Lenovo BladeCenter HX5 1909 Problem Determination And Service Manual Download Page 177

Page: 177 / 313

• Follow the suggested actions in the order in which they are listed in the Action column until the problem is

solved.

• See “

Parts listing - BladeCenter HX5

” on page 57 to determine which components are customer replaceable

units (CRU) and which components are field replaceable units (FRU).

• If an action step is preceded by “(Trained service technician only),” that step must be performed only by a

Trained service technician.

Error code

Description

Action

3818001

Core Root of Trust
Measurement (CRTM)
update failed

1. Revert to a previous version of the firmware for the blade server.

2. If the blade server will not start, switch to the backup UEFI image.

Set switch 7 to the on position. See “System-board switches” on
page 13 for the location of switch 7.

3. Update the firmware for the server. Make sure that you are using the

latest firmware from http://www.ibm.com/support/ fixcentral/
systemx/groupView? query.productGroup=ibm%2FBladeCenter.

4. Set switch 7 to the off position. See “System-board switches” on

page 13 for the location of switch 7.

3818002

Core Root of Trust
Measurement (CRTM)
update aborted

1. Revert to a previous version of the firmware for the blade server.

2. If the blade server will not start, switch to the backup UEFI image.

Set switch 7 to the on position. See “System-board switches” on
page 13 for the location of switch 7.

3. Update the firmware for the server. Make sure that you are using the

latest firmware from http://www.ibm.com/support/ fixcentral/
systemx/groupView? query.productGroup=ibm%2FBladeCenter.

4. Set switch 7 to the off position. See “System-board switches” on

page 13 for the location of switch 7.

3818003

Core Root of Trust
Measurement (CRTM) flash
lock failed

1. Revert to a previous version of the firmware for the blade server.

2. If the blade server will not start, switch to the backup UEFI image.

Set switch 7 to the on position. See “System-board switches” on
page 13 for the location of switch 7.

3. Update the firmware for the server. Make sure that you are using the

latest firmware from http://www.ibm.com/support/ fixcentral/
systemx/groupView? query.productGroup=ibm%2FBladeCenter.

4. Set switch 7 to the off position. See “System-board switches” on

page 13 for the location of switch 7.

3818004

Core Root of Trust
Measurement (CRTM)
system error

1. Revert to a previous version of the firmware for the blade server.

2. If the blade server will not start, switch to the backup UEFI image.

Set switch 7 to the on position. See “System-board switches” on
page 13 for the location of switch 7.

3. Update the firmware for the server. Make sure that you are using the

latest firmware from http://www.ibm.com/support/ fixcentral/
systemx/groupView? query.productGroup=ibm%2FBladeCenter.

4. Set switch 7 to the off position. See “System-board switches” on

page 13 for the location of switch 7.

Chapter 5

Diagnostics

161

Summary of Contents for BladeCenter HX5 1909


























































































































































































































































































































Search results

Summary of Contents for BladeCenter HX5 1909

Reviews:

Related manuals for BladeCenter HX5 1909

Brands by name

Popular brands

Lenovo BladeCenter HX5 1909, Problem Determination And Service Manual

Search results

Summary of Contents for BladeCenter HX5 1909

Reviews:

Related manuals for BladeCenter HX5 1909

Brands by name

Popular brands