Lenovo BladeCenter HX5 1909 Problem Determination And Service Manual Download Page 145

Page: 145 / 313

the rack in which you are installing the control panel for at least 2 seconds; then, remove the USB
module from its package.

Step 11. Orient the control panel so that the front of the control panel is facing the bezel.

Step 12. Use your fingers to insert the LEDs on the control panel into the holes on the bezel.

Step 13. Rotate the control panel down and press down until it is seated.

Step 14. Install the access panel:

There are two types of access panels available for the BladeCenter HX5 blade server, depending
on whether tall heat sinks are installed.

• Complete the following steps to install the access panel on a BladeCenter HX5 blade server that

does not have tall heat sinks:

1. Make sure that the screws on the access panel are in the open position (the screw insert is

parallel to the side of the access panel).

2. Slide the back of the cover under the blade server bezel, aligning the screws with the slots

on the blade server.

3. Using a screwdriver or a coin, turn each of the screws away from the middle of the blade

server until it is in the locked position.

• Complete the following steps to install the operator control panel access panel on a BladeCenter

HX5 blade server that does have tall heat sinks:

Chapter 4

Removing and replacing blade server components

129

Summary of Contents for BladeCenter HX5 1909


























































































































































































































































































































Search results

Summary of Contents for BladeCenter HX5 1909

Reviews:

Related manuals for BladeCenter HX5 1909

Brands by name

Popular brands

Lenovo BladeCenter HX5 1909, Problem Determination And Service Manual

Search results

Summary of Contents for BladeCenter HX5 1909

Reviews:

Related manuals for BladeCenter HX5 1909

Brands by name

Popular brands