Lenovo BladeCenter HX5 1909 Problem Determination And Service Manual Download Page 172

Page: 172 / 313

• Follow the suggested actions in the order in which they are listed in the Action column until the problem is

solved.

• See “

Parts listing - BladeCenter HX5

” on page 57 to determine which components are customer replaceable

units (CRU) and which components are field replaceable units (FRU).

• If an action step is preceded by “(Trained service technician only),” that step must be performed only by a

Trained service technician.

Error code

Description

Action

00580A1

Invalid DIMM population for
mirroring mode.

1. Make sure that the server contains the correct number of DIMMs, in

the correct order (see “Installing a DIMM - BladeCenter HX5” on
page 104).

2. Check the system event log for any memory errors that might be

related to the specified DIMM and resolve those errors.

Note:

If the system event log is full, new events will not be posted to

the log. You can clear the system event log through the Setup Utility
(see “Using the Setup utility” on page 20). Select

System Event

Logs

and then select

Clear System Event Log

3. Reseat the DIMMs (see “Removing a DIMM - BladeCenter HX5” on

page 103 and “Installing a DIMM - BladeCenter HX5” on page 104)
and restart the blade server.

4. Remove the specified DIMM pair and replace the DIMM pair with an

identical pair of known good DIMMs, and then restart the server.
Repeat as necessary. If the failures continue, go to step 5 on page
156.

5. (Trained service technician only) Replace the system board (see

“Removing the system-board assembly - BladeCenter HX5” on page
140 and “Installing the system-board assembly - BladeCenter HX5”
on page 142).

00580A4

Memory population
changed.

Information only. Memory has been added, moved, or changed.

00580A5

Mirror failover complete

Information only. Memory redundancy has been lost. Check the system-
event log for uncorrected DIMM failure events.

00580B0

Memory SMI link failure

1. Check the IBM support website for an applicable retain tip or

firmware update that applies to this memory error.

2. Check the DIMM connector and the associated microprocessor

connector (make sure you use the microprocessor installation and
removal tool).

3. (Trained service technician only) If the connector is damaged,

replace the system board assembly (see “Removing the system-
board assembly - BladeCenter HX5” on page 140 and “Installing the
system-board assembly - BladeCenter HX5” on page 142).

00580B1

Memory SMI lane fail down

Information only.

156

BladeCenter HX5 Blade ServerProblem Determination and Service Guide

Summary of Contents for BladeCenter HX5 1909


























































































































































































































































































































Search results

Summary of Contents for BladeCenter HX5 1909

Reviews:

Related manuals for BladeCenter HX5 1909

Brands by name

Popular brands

Lenovo BladeCenter HX5 1909, Problem Determination And Service Manual

Search results

Summary of Contents for BladeCenter HX5 1909

Reviews:

Related manuals for BladeCenter HX5 1909

Brands by name

Popular brands