Lenovo BladeCenter HX5 1909 Problem Determination And Service Manual Download Page 119

Page: 119 / 313

Step 15. Install the CFFh expansion card, if you removed one from the blade server (see “Installing a CFFh

expansion card” on page 122 for instructions).

Step 16. If the blade server is part of a scalable blade complex, assemble the scalable blade complex (see

“Assembling a scalable blade complex” on page 70 for instructions).

Step 17. Install the IBM MAX5 expansion blade if you removed one (see “Installing an IBM MAX5 expansion

blade” on page 88 for instructions).

Step 18. Install the optional expansion unit, if you removed one from the blade server (see “Installing an

expansion unit” on page 97 for instructions).

Step 19. Install the cover onto the blade server (see “Installing the blade server cover” on page 73 for

instructions).

Step 20. Install the blade server or scalable blade complex into the BladeCenter chassis (see “Installing a

blade server in a BladeCenter chassis” on page 67 for instructions).

Removing a DIMM - BladeCenter HX5

Use this information to remove a dual inline memory module (DIMM) from the blade server.

The following illustration shows how to remove a DIMM from the blade server.

To remove a DIMM, complete the following steps:

Step 1. Before you begin, read “Safety” on page v and “Installation guidelines” on page 65.

Step 2. If the blade server or scalable blade complex is installed in a BladeCenter chassis, remove it. See

“Removing the blade server from the BladeCenter chassis” on page 66 for instructions.

Step 3. Carefully lay the blade server on a flat, static-protective surface.

Step 4. If you are removing the DIMM from a blade server that is the bottom blade server in a scalable

blade complex, disassemble the blade complex (see “Disassembling a scalable blade complex” on
page 68 for instructions).

Step 5. If an IBM MAX5 expansion blade is installed, remove it (see “Removing an IBM MAX5 expansion

blade” on page 87 for instructions).

Step 6. Open the blade server cover (see “Removing the blade server cover” on page 71 for instructions).

Step 7. If an optional expansion unit is installed, remove the expansion unit (see “Removing an expansion

unit” on page 96 for instructions).

Note:

Optional expansion units are not supported when a IBM MAX5 expansion blade is installed.

Chapter 4

Removing and replacing blade server components

103

Summary of Contents for BladeCenter HX5 1909


























































































































































































































































































































Search results

Summary of Contents for BladeCenter HX5 1909

Reviews:

Related manuals for BladeCenter HX5 1909

Brands by name

Popular brands

Lenovo BladeCenter HX5 1909, Problem Determination And Service Manual

Search results

Summary of Contents for BladeCenter HX5 1909

Reviews:

Related manuals for BladeCenter HX5 1909

Brands by name

Popular brands