manualshive.com logo in svg

Lenovo BladeCenter HX5 1909, Problem Determination And Service Manual

Introducing the Lenovo BladeCenter HX5 1909, a high-performance server built for efficiency and reliability. Need assistance with troubleshooting or servicing? Look no further! Download the Problem Determination And Service Manual for free, exclusively from manualshive.com. Get the help you need to optimize your Lenovo BladeCenter HX5 1909's performance today!

Share
Download
background image

TIGHTEN

SCREWS

AL
TERNA

TEL

Y

SSD
expansion
card

CIOv
expansion
card

CFFh
expansion
card

For information about installing an SSD expansion card, see “Installing an SSD expansion card” on page 99.

To determine which expansion cards are supported in the BladeCenter HX5 blade server, see http://www. 
ibm.com/ servers/eserver/serverproven/compat/us/.

Product documentation for expansion cards is available at “” on page .

Installing a CFFh expansion card

Use these instructions to install a compact-form-factor expansion card in the blade server.

The blade server supports a horizontal-combination-form-factor (CFFh) expansion card. The following 
illustration shows how to install a CFFh expansion card.

Expansion
card

Expansion
card
standoff

To install a CFFh expansion card, complete the following steps:

Step 1.  Before you begin, read “Safety” on page v and “Installation guidelines” on page 65.

Step 2.  If the blade server or scalable blade complex is installed in a BladeCenter chassis, remove it. See 

“Removing the blade server from the BladeCenter chassis” on page 66 for instructions.

Step 3.  Carefully lay the blade server on a flat, static-protective surface.

Step 4.  If an optional expansion unit is installed, remove the expansion unit (see “Removing an expansion 

unit” on page 96 for instructions). 

Note: 

Optional expansion units are not supported when a IBM MAX5 expansion blade is installed.

122

BladeCenter HX5 Blade ServerProblem Determination and Service Guide

Summary of Contents for BladeCenter HX5 1909


























































































































































































































































































































Reviews:

No comments

Related manuals for BladeCenter HX5 1909

Wyse C00LE Quick Start Manual preview
C00LE
Brand: Wyse Pages: 6
Rasilient ApplianceStor 15MT User Manual preview
ApplianceStor 15MT
Brand: Rasilient Pages: 30
Intel SRPM8 Quick Start Manual preview
SRPM8
Brand: Intel Pages: 32
PalatiumCare Palcare PAL-211401 Install Manual preview
Palcare PAL-211401
Brand: PalatiumCare Pages: 64
Dell PowerEdge M630 Owner'S Manual preview
PowerEdge M630
Brand: Dell Pages: 129
Dell PowerEdge HR675 Hardware Owner'S Manual preview
PowerEdge HR675
Brand: Dell Pages: 194
Dell PowerEdge FC630 Owner'S Manual preview
PowerEdge FC630
Brand: Dell Pages: 143
Dell PowerEdge HX574 Hardware Owner'S Manual preview
PowerEdge HX574
Brand: Dell Pages: 202
Dell Wyse 5020 P Series Quick Start Manual preview
Wyse 5020 P Series
Brand: Dell Pages: 8
Dell Wyse 3020 Quick Start Up Manual preview
Wyse 3020
Brand: Dell Pages: 2
Dell Wyse 5030 User Manual preview
Wyse 5030
Brand: Dell Pages: 12
Dell Wyse 5000 Series Quick Start Manual preview
Wyse 5000 Series
Brand: Dell Pages: 8
Dell Wyse7020 Quick Start Manual preview
Wyse7020
Brand: Dell Pages: 2
Dell Wyse 3030 Quick Start Manual preview
Wyse 3030
Brand: Dell Pages: 2
Dell Wyse 5020 Quick Start Manual preview
Wyse 5020
Brand: Dell Pages: 8
Dell XC6320 Owner'S Manual preview
XC6320
Brand: Dell Pages: 91
Dell Wyse 3030 LT User Manual preview
Wyse 3030 LT
Brand: Dell Pages: 43
Dell PowerEdge FD332 Owner'S Manual preview
PowerEdge FD332
Brand: Dell Pages: 46

Brands by name

Popular brands

Load more brands