Lenovo BladeCenter HX5 1909 Problem Determination And Service Manual Download Page 115

Page: 115 / 313

Step 3. Carefully lay the blade server on a flat, static-protective surface.

Step 4. If you are removing the SSD expansion card from a blade server that is the bottom blade server in a

scalable blade complex, disassemble the blade complex (see “Disassembling a scalable blade
complex” on page 68 for instructions).

Step 5. If an optional expansion unit is installed, remove the expansion unit (see “Removing an expansion

unit” on page 96 for instructions).

Note:

Optional expansion units are not supported when a IBM MAX5 expansion blade is installed.

Step 6. If an IBM MAX5 expansion blade is installed, remove it (see “Removing an IBM MAX5 expansion

blade” on page 87 for instructions).

Step 7. Open the blade server cover (see “Removing the blade server cover” on page 71 for instructions).

Step 8. If a CFFh expansion card is installed, remove it (see “Removing a CFFh expansion card” on page

119 for instructions).

Step 9. Locate the blue expansion card lever on the SSD expansion card and lift the lever to release the

SSD expansion card from the blade expansion connector on the system board.

Step 10. Rotate the SSD expansion card up and lift it away from the expansion-card standoffs.

Expansion
card

Expansion
card
standoff

Release
handle

Expansion
card
standoff

Step 11. If you are instructed to return the SSD expansion card, follow all packaging instructions, and use

any packaging materials for shipping that are supplied to you.

Installing an SSD expansion card

Use this information to install an SSD expansion card.

To install an SSD expansion card, complete the following steps:

Step 1. Before you begin, read “Safety” on page v and “Installation guidelines” on page 65.

Step 2. If the blade server or scalable blade complex is installed in a BladeCenter chassis, remove it. See

“Removing the blade server from the BladeCenter chassis” on page 66 for instructions.

Step 3. Carefully lay the blade server on a flat, static-protective surface.

Step 4. If you are installing the SSD expansion card in a blade server that is the bottom blade server in an

existing scalable blade complex, disassemble the blade complex (see “Disassembling a scalable
blade complex” on page 68 for instructions).

Chapter 4

Removing and replacing blade server components

Summary of Contents for BladeCenter HX5 1909


























































































































































































































































































































Search results

Summary of Contents for BladeCenter HX5 1909

Reviews:

Related manuals for BladeCenter HX5 1909

Brands by name

Popular brands

Lenovo BladeCenter HX5 1909, Problem Determination And Service Manual

Search results

Summary of Contents for BladeCenter HX5 1909

Reviews:

Related manuals for BladeCenter HX5 1909

Brands by name

Popular brands