Lenovo BladeCenter HX5 1909 Problem Determination And Service Manual Download Page 78 | Manualshive

Page: 78 / 313

background image

Parts listing - IBM MAX5

The following replaceable components are available for the IBMIBM MAX5 expansion blade. There are two
versions of the IBM MAX5 expansion blade, referred to as the IBM MAX5 version 1 and IBM MAX5 version 2
in this document. IBM MAX5 version 2 has a "MAX5" identifying label on the bottom of the front bezel. The
functionality of the two IBM MAX5 expansion blades are equivalent except for the type of DIMMs supported.
The type of DIMMs supported will differ, depending on the version of IBM MAX5 expansion blade installed.

For an updated parts listing on the web, complete the following steps.

Note:

Changes are made periodically to the IBM website. The actual procedure might vary slightly from what

is described in this document.

1. Go to http://www.ibm.com/supportportal/.

2. Under

Product support

, click

BladeCenter

.

3. Under

Popular links

, click

Part documents lookup

.

4. From the

Product Family

menu, select

BladeCenter HX5

and click

Go

.

Note:

The illustrations in this document might differ slightly from your hardware.

Replaceable components are of four types:

•

Tier 1 customer replaceable unit (CRU):

Replacement of Tier 1 CRUs is your responsibility. If IBM

installs a Tier 1 CRU at your request, you will be charged for the installation.

•

Tier 2 customer replaceable unit:

You may install a Tier 2 CRU yourself or request IBM to install it, at no

additional charge, under the type of warranty service that is designated for your server.

•

Field replaceable unit (FRU):

FRUs must be installed only by trained service technicians.

62

BladeCenter HX5 Blade ServerProblem Determination and Service Guide

«
...
76
77
78
79
80
...
»

Summary of Contents for BladeCenter HX5 1909


























































































































































































































































































































Reviews:

No comments

Related manuals for BladeCenter HX5 1909

QS21 - BladeCenter - 0792

Brand: IBM Pages: 110

Brand: Sercomm Pages: 75

AirLive WP-203G

Brand: Ovislink Pages: 132

Transport TX46 (B4985) Service

Brand: TYAN Pages: 75

Brand: d3 Technologies Pages: 10

A+ AS-2124US-TNRP

Brand: Supermicro Pages: 130

x3350 - System - 4192

Brand: IBM Pages: 98

x3500 - System - 7977

Brand: IBM Pages: 124

Brand: IBM Pages: 106

x3200 - System M3 - 7328

Brand: IBM Pages: 100

System x3400 Type 7975

Brand: IBM Pages: 124

System x3300 M4

Brand: IBM Pages: 470

System x iDataPlex dx360

Brand: IBM Pages: 26

Brand: Moxa Technologies Pages: 100

PRIMERGY RX300 S6

Brand: Fujitsu Pages: 132

PRIMERGY RX300 S5

Brand: Fujitsu Pages: 112

PRIMERGY RX2540 M4

Brand: Fujitsu Pages: 86

PRIMERGY RX2540 M6

Brand: Fujitsu Pages: 121

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands