Lenovo BladeCenter HX5 1909 Problem Determination And Service Manual Download Page 195

Page: 195 / 313

• Follow the suggested actions in the order in which they are listed in the Action column until the problem is

solved.

• See “

Parts listing - BladeCenter HX5

” on page 57 to determine which components are CRUs and which

components are FRUs.

• If an action step is preceded by “(Trained service technician only),” that step must be performed only by a

trained service technician.

Type

Error Message

Action

Error

Processor

(CPU

Status) internal

error [Note

=1,2]

1. Remove the blade server and ensure the processors are

installed correctly (see “Installing a microprocessor and
heat sink” on page 134).

2. Verify that the system is running the latest UEFI firmware

(see “Updating firmware and device drivers” on page 30).

3. Run the Setup utility (see “Using the Setup utility” on page

20).

a. Make sure that both processors are displayed by the

system.

b. Load the default settings.

c. Go to the

System Settings

menu and make sure the

processor is enabled.

4. (Trained service technician only) Replace the processor

(see “Removing a microprocessor and heat sink” on page
130 and “Installing a microprocessor and heat sink” on
page 134).

5. (Trained service technician only) Replace the system-

board assembly (see “Removing the system-board
assembly - BladeCenter HX5” on page 140 and “Installing
the system-board assembly - BladeCenter HX5” on page
142).

Error Code: 0x806F0009

Information

System board (Host Power) power
on/off

Information only; no action is required.

Error Code: 0x806F000D

Information

Hard drive

(SSD Exp Drive

)

removed/installed [Note

=1,2]

Information only; no action is required.

Error Code: 0x806F000F

Note:

Multiple events can be displayed for this error code. Be sure to read the message text to determine the

appropriate recovery actions.

Error

FW/BIOS, firmware progress
(Firmware Error) FW/BIOS ROM
corruption

Install the latest UEFI firmware (see “Updating firmware and
device drivers” on page 30).

Chapter 5

Diagnostics

179

Summary of Contents for BladeCenter HX5 1909


























































































































































































































































































































Search results

Summary of Contents for BladeCenter HX5 1909

Reviews:

Related manuals for BladeCenter HX5 1909

Brands by name

Popular brands

Lenovo BladeCenter HX5 1909, Problem Determination And Service Manual

Search results

Summary of Contents for BladeCenter HX5 1909

Reviews:

Related manuals for BladeCenter HX5 1909

Brands by name

Popular brands