Lenovo BladeCenter HX5 1909 Problem Determination And Service Manual Download Page 146 | Manualshive

Page: 146 / 313

background image

1. Align the holes in the access panel with the holes in the blade server.

2. Use a screwdriver to install the screws in the holes of the access panel.

Step 15. If the blade server is part of a scalable blade complex, assemble the scalable blade complex (see

“Assembling a scalable blade complex” on page 70 for instructions).

Step 16. Install the IBM MAX5 expansion blade if you removed one (see “Installing an IBM MAX5 expansion

blade” on page 88 for instructions).

Step 17. Install the optional expansion unit, if you removed one from the blade server (see “Installing an

expansion unit” on page 97 for instructions).

Step 18. Install the cover onto the blade server (see “Installing the blade server cover” on page 73 for

instructions).

Step 19. Install the blade server or scalable blade complex into the BladeCenter chassis (see “Installing a

blade server in a BladeCenter chassis” on page 67 for instructions).

Removing and replacing field replaceable units

Use this information to remove and replace field replaceable units (FRUs). FRUs must be installed only by
trained service technicians.

Note:

The illustrations in this document might differ slightly from your hardware.

Removing a microprocessor and heat sink

Use this information to remove a microprocessor and heat sink from the blade server.

Read the following important guidelines before you remove a microprocessor that is not faulty (for example,
when you are replacing the system-board assembly).

If you are not replacing a defective heat sink or microprocessor, the thermal material on the heat sink and
microprocessor will remain effective if you carefully handle the heat sink and microprocessor when you
remove or install these components. Do not touch the thermal material or otherwise allow it to become
contaminated.

Notes:

1. The microprocessor and heat-sink assembly are both field replaceable units (FRUs) and must be

replaced by a trained service technician. To contact an IBM service representative, see “Hardware
service and support” on page 279.

130

BladeCenter HX5 Blade ServerProblem Determination and Service Guide

«
...
144
145
146
147
148
...
»

Summary of Contents for BladeCenter HX5 1909


























































































































































































































































































































Reviews:

No comments

Related manuals for BladeCenter HX5 1909

Enterprise Server S80

Brand: IBM Pages: 282

HS12 - BladeCenter - 8028

Brand: IBM Pages: 204

Brand: Xantech Pages: 52

3CRWPS10075-US - OfficeConnect Wireless 54Mbps 11g Print...

Brand: 3Com Pages: 94

Brand: Raidon Pages: 20

Brand: IBM Pages: 36

Brand: Discover Video Pages: 148

Brand: Airlink101 Pages: 36

Brand: QNAP Pages: 203

Brand: IBM Pages: 2

System x3100 M4

Brand: IBM Pages: 35

eServer xSeries 345 Type 8670

Brand: IBM Pages: 71

eServer 445 xSeries

Brand: IBM Pages: 124

pSeries 615 Model 6C3

Brand: IBM Pages: 208

Multiprise 3000

Brand: IBM Pages: 264

Redboks System x3550 M4

Brand: IBM Pages: 820

Brand: Inventec Pages: 129

Brand: Black Box Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands