Lenovo BladeCenter HX5 1909 Problem Determination And Service Manual Download Page 152 | Manualshive

Page: 152 / 313

background image

Microprocessor
retainer

Microprocessor
release lever

a. Rotate the release lever on the microprocessor socket from its closed and locked position until

it stops in the fully open position (approximately a 135° angle).

b. Rotate the microprocessor retainer on the microprocessor socket from its closed position until

it stops in the fully open position (approximately a 135° angle).

Step 10. If a dust cover is installed over the microprocessor socket, lift the dust cover from the socket and

store it in a safe place.

Step 11. Install the microprocessor in the microprocessor installation tool.

Attention:

If you are installing E7 series microprocessors in the blade server, you must use the

microprocessor installation tool with the text “X7500 + E7” on the bottom of the tool (see the
following illustration). Tools that do not have this text on the bottom will not work correctly with the
E7 series microprocessors.

X7500

+

E7

a. Remove the static-protective bag and the foam surrounding the bag from the box.

b. Touch the static-protective bag that contains the new microprocessor to any

unpainted

surface on the BladeCenter chassis or any

unpainted

metal surface on any other grounded

rack component.

c. Carefully remove the microprocessor from the static-protective bag, touching only the edges

of the microprocessor.

d. If there is a plastic protective cover on the bottom of the microprocessor, carefully remove it.

136

BladeCenter HX5 Blade ServerProblem Determination and Service Guide

«
...
150
151
152
153
154
...
»

Summary of Contents for BladeCenter HX5 1909


























































































































































































































































































































Reviews:

No comments

Related manuals for BladeCenter HX5 1909

BladeCenter HS23

Brand: IBM Pages: 28

eserver pSeries 690

Brand: IBM Pages: 142

eServer 370 xSeries

Brand: IBM Pages: 218

BladeCenter PS703

Brand: IBM Pages: 298

BladeCenter T Type 8720

Brand: IBM Pages: 180

Brand: Wyse Pages: 6

AssuredSAN 4004 Series

Brand: Dot Hill Pages: 59

DiskStation Series

Brand: Synology Pages: 6

AND-APL1E Series

Brand: Acrosser Technology Pages: 42

PS121v2 - USB Mini Print Server

Brand: NETGEAR Pages: 50

Brand: NETGEAR Pages: 124

Digital Entertainer HD EVA8000

Brand: NETGEAR Pages: 114

Smartstor NS4600

Brand: Promise Technology Pages: 370

Brand: Solid Pages: 102

DeviceMaster LT

Brand: Comtrol Pages: 136

Brand: IBM Pages: 68

206m - eServer xSeries - 8485

Brand: IBM Pages: 92

Brand: pachanko Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands