Lenovo BladeCenter HX5 1909 Problem Determination And Service Manual Download Page 204

Page: 204 / 313

• Follow the suggested actions in the order in which they are listed in the Action column until the problem is

solved.

• See “

Parts listing - BladeCenter HX5

” on page 57 to determine which components are CRUs and which

components are FRUs.

• If an action step is preceded by “(Trained service technician only),” that step must be performed only by a

trained service technician.

Type

Error Message

Action

Error

Interconnect 5 (SideScale Card)
configuration error

1. Reseat the scalable blade complex (see “Removing the

blade server from the BladeCenter chassis” on page 66
and “Installing a blade server in a BladeCenter chassis” on
page 67).

2. Reseat the scalability expansion card (see “Removing the

2-node scalability card” on page 83 and “Installing the 2-
node Scalability card” on page 85, or “Removing the 1-
node speed burst card” on page 81 and “Installing the 1-
node speed burst card” on page 82).

3. Update the firmware for the blade server (see “Updating

firmware and device drivers” on page 30).

4. Replace the scalability expansion card (see “Removing the

5. (Trained service technician only) Replace the system-

board assembly (see “Removing the system-board
assembly - BladeCenter HX5” on page 140 and “Installing
the system-board assembly - BladeCenter HX5” on page
142).

Error

Interconnect 5 (Unknown Scale ID)
configuration error

1. Reseat the scalable blade complex (see “Removing the

blade server from the BladeCenter chassis” on page 66
and “Installing a blade server in a BladeCenter chassis” on
page 67).

2. Reseat the scalability expansion card (see “Removing the

3. Attempt to create the hardware partition again (see

“Working with a scalable blade complex” on page 16).

4. Update the firmware for the blade server (see “Updating

firmware and device drivers” on page 30).

5. Replace the scalability expansion card (see “Removing the

6. (Trained service technician only) Replace the system-

board assembly (see “Removing the system-board
assembly - BladeCenter HX5” on page 140 and “Installing
the system-board assembly - BladeCenter HX5” on page
142).

Error Code: 0x806F012B

188

BladeCenter HX5 Blade ServerProblem Determination and Service Guide

Summary of Contents for BladeCenter HX5 1909


























































































































































































































































































































Search results

Summary of Contents for BladeCenter HX5 1909

Reviews:

Related manuals for BladeCenter HX5 1909

Brands by name

Popular brands

Lenovo BladeCenter HX5 1909, Problem Determination And Service Manual

Search results

Summary of Contents for BladeCenter HX5 1909

Reviews:

Related manuals for BladeCenter HX5 1909

Brands by name

Popular brands