Lenovo BladeCenter HX5 1909 Problem Determination And Service Manual Download Page 101

Page: 101 / 313

Installing the 2-node Scalability card

Use this information to install the 2-node scalability card on a blade server.

To install the 2-node scalability card, complete the following steps:

Step 1. Before you begin, read “Safety” on page v and “Installation guidelines” on page 65.

Step 2. If the blade servers are installed in a BladeCenter chassis, remove them (see “Removing the blade

server from the BladeCenter chassis” on page 66 for instructions).

Step 3. If an optional expansion unit is installed, remove the expansion unit (see “Removing an expansion

unit” on page 96 for instructions).

Note:

Optional expansion units are not supported when a IBM MAX5 expansion blade is installed.

Step 4. Remove the covers for both blade servers (see “Removing the blade server cover” on page 71 for

instructions).

Step 5. Remove the 1-node speed burst cards (see “Installing the 1-node speed burst card” on page 82) or

scalability fillers from both blade servers, depending on which you have installed.To remove the
scalability filler, complete the following steps:

a. Using the 3/16" hex driver that comes with the scalability kit, loosen the nut that attaches the

filler to the blade server.

b. Lift the filler off of the blade server.

Step 6. Attach the scalability tray to the topmost blade server (see “Installing the scalability tray” on page

80).

Step 7. Attach the blade server with the scalability tray to the bottom blade server.

Blade server
cover release

Cover
Pins

a. Lower the topmost blade server so that the slots at the rear slide down onto the pins at the rear

of the bottom blade server, as shown in the illustration.

b. Pivot the topmost blade server to the closed position, as shown in the illustration, until it clicks

into place.

Step 8. Stand the blade servers upright on a clean, flat work surface, with the scalability connector on the

blade servers facing up.

Chapter 4

Removing and replacing blade server components

Summary of Contents for BladeCenter HX5 1909


























































































































































































































































































































Search results

Summary of Contents for BladeCenter HX5 1909

Reviews:

Related manuals for BladeCenter HX5 1909

Brands by name

Popular brands

Lenovo BladeCenter HX5 1909, Problem Determination And Service Manual

Search results

Summary of Contents for BladeCenter HX5 1909

Reviews:

Related manuals for BladeCenter HX5 1909

Brands by name

Popular brands