Lenovo BladeCenter HX5 1909 Problem Determination And Service Manual Download Page 130

Page: 130 / 313

1. Using a screwdriver or a coin, turn each of the screws toward the middle of the blade server

until they are in the unlocked position.

2. While you lift the back of the access panel, slide the panel away from the bezel.

• Complete the following steps to remove the embedded hypervisor card access panel on a

BladeCenter HX5 blade server that does have tall heat sinks:

1. Using a screwdriver, remove each of the screws on the right access panel.

2. Lift the access panel away from the blade server.

Step 9. Locate the hypervisor interposer on the system board (see “Parts listing - BladeCenter HX5” on

page 57).

Step 10. Press down on the front edge of the hypervisor interposer to disengage the hypervisor interposer

from the hypervisor interposer card guide.

114

BladeCenter HX5 Blade ServerProblem Determination and Service Guide

Summary of Contents for BladeCenter HX5 1909


























































































































































































































































































































Search results

Summary of Contents for BladeCenter HX5 1909

Reviews:

Related manuals for BladeCenter HX5 1909

Brands by name

Popular brands

Lenovo BladeCenter HX5 1909, Problem Determination And Service Manual

Search results

Summary of Contents for BladeCenter HX5 1909

Reviews:

Related manuals for BladeCenter HX5 1909

Brands by name

Popular brands