Lenovo BladeCenter HX5 1909 Problem Determination And Service Manual Download Page 73 | Manualshive

Page: 73 / 313

background image

Chapter 3. Parts listing

This chapter contains the parts listing for the BladeCenter HX5 blade server and the IBM MAX5 expansion
blade.

Parts listing - BladeCenter HX5

The following replaceable components are available for the IBMIBM BladeCenter HX5 Type 7873, 7872,
1910, and 1909 blade servers. For an updated parts listing on the web, complete the following steps.

Note:

Changes are made periodically to the IBM website. The actual procedure might vary slightly from what

is described in this document.

1. Go to http://www.ibm.com/supportportal/.

2. Under

Product support

, click

BladeCenter

.

3. Under

Popular links

, click

Part documents lookup

.

4. From the

Product Family

menu, select

BladeCenter HX5

and click

Go

.

Note:

The illustrations in this document might differ slightly from your hardware.

Replaceable components are of the following types:

© Copyright Lenovo 2017

57

«
...
71
72
73
74
75
...
»

Summary of Contents for BladeCenter HX5 1909


























































































































































































































































































































Reviews:

No comments

Related manuals for BladeCenter HX5 1909

BladeCenter HS23

Brand: IBM Pages: 28

NECCare Platinum Express5800/A1160

Brand: NEC Pages: 4

NECCare Gold Express5800/320Fd

Brand: NEC Pages: 11

NEC Express5800/R120d-2E

Brand: NEC Pages: 39

UNIVERGE NEAX 2000 IPS

Brand: NEC Pages: 244

UNIVERGE NEAX 2000 IPS

Brand: NEC Pages: 191

UNIVERGE NEAX 2000 IPS

Brand: NEC Pages: 96

Brand: Lantronix Pages: 299

Brand: Sun Microsystems Pages: 128

Brand: Synology Pages: 15

Brand: TYAN Pages: 170

DocuColor 45087638

Brand: Xerox Pages: 28

Brand: MSI Pages: 54

iPlanet Web Server

Brand: Sun Microsystems Pages: 62

Brand: Emerson Pages: 23

DIXELL XWEB5000 PRO

Brand: Emerson Pages: 20

Brand: Emerson Pages: 18

Avocent ACS 6000

Brand: Emerson Pages: 93

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands