Lenovo BladeCenter HX5 1909 Problem Determination And Service Manual Download Page 96

Page: 96 / 313

Step 10. Lift the scalability tray away from the blade server.

Step 11. If you are instructed to return the scalability tray, follow all packaging instructions, and use any

packaging materials for shipping that are supplied to you.

Installing the scalability tray

Use this information to install the scalability tray on a blade server.

To install the scalability tray, complete the following steps:

Step 1. Before you begin, read “Safety” on page v and “Installation guidelines” on page 65.

Step 2. If the blade server is installed in a BladeCenter chassis, remove it (see “Removing the blade server

from the BladeCenter chassis” on page 66 for instructions).

Step 3. Carefully lay the blade server on a flat, static-protective surface, with the cover side down.

Step 4. Align the scalability tray flush with the blade server in the start position. The pins on the scalability

tray should be aligned with the holes in the blade server.

Step 5. Pressing down firmly on the middle of the tray, slide the scalability tray forward toward the bezel

until there is an audible click from each side of the blade server.

BladeCenter HX5 Blade ServerProblem Determination and Service Guide

Summary of Contents for BladeCenter HX5 1909


























































































































































































































































































































Search results

Summary of Contents for BladeCenter HX5 1909

Reviews:

Related manuals for BladeCenter HX5 1909

Brands by name

Popular brands

Lenovo BladeCenter HX5 1909, Problem Determination And Service Manual

Search results

Summary of Contents for BladeCenter HX5 1909

Reviews:

Related manuals for BladeCenter HX5 1909

Brands by name

Popular brands