Lenovo BladeCenter HX5 1909 Problem Determination And Service Manual Download Page 149 | Manualshive

Page: 149 / 313

background image

Step 11. Rotate the locking lever on the microprocessor socket from its closed and locked position until it

stops in the fully open position (approximately a 135° angle). Lift the microprocessor retainer cover
upward.

Attention:

Do not touch the connectors on the microprocessor and the microprocessor socket.

Step 12. Find the microprocessor installation tool that came with the new microprocessor.

Attention:

If you are removing E7 series microprocessors, you must use the microprocessor

installation tool with the text “X7500 + E7” on the bottom of the tool (see the following illustration).
Tools that do not have this text on the bottom will not work correctly with the E7 series
microprocessors.

X7500

+

E7

Step 13. Place the microprocessor installation tool down over the microprocessor, aligning the holes on the

tool with the screws on the microprocessor bracket.

Note:

The alignment holes on the tool will not sit flush on the microprocessor bracket screws.

However, the holes can be used as a guide to ensure the proper alignment between the
microprocessor installation tool and the microprocessor bracket.

Step 14. Twist the handle clockwise to attach the tool to the microprocessor.

Note:

You can pick up or release the microprocessor by twisting the microprocessor installation

tool handle.

Installation
tool

Microprocessor

Alignment
holes

Screws

Handle

Step 15. Carefully lift the microprocessor straight up and out of the socket, and place it on a static-

protective surface.

Removing and replacing blade server components

133

«
...
147
148
149
150
151
...
»

Summary of Contents for BladeCenter HX5 1909


























































































































































































































































































































Reviews:

No comments

Related manuals for BladeCenter HX5 1909

Brand: IBM Pages: 64

Brand: IBM Pages: 214

Brand: TANDBERG Pages: 127

Brand: Xerox Pages: 40

Brand: B&B Pages: 70

244857-001 - TaskSmart - C4000 Model 60_duplicate

Brand: Compaq Pages: 9

FusionServer 1288H V5

Brand: xFusion Digital Technologies Pages: 96

Brand: Olive Pages: 103

Brand: QNAP Pages: 49

Brand: Samsung Pages: 58

SnapServer Expansion E2000

Brand: Overland Storage Pages: 5

Brand: Overland Storage Pages: 133

ZXCLOUD iBOX CT320

Brand: Zte Pages: 17

Brand: Planet Pages: 28

Dual Processor AS 1020C-3

Brand: Supero Pages: 106

AS2041M-32R Plus

Brand: Supero Pages: 106

Brand: UNV Pages: 27

Brand: GIGA-BYTE TECHNOLOGY Pages: 120

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands