Lenovo BladeCenter HX5 1909 Problem Determination And Service Manual Download Page 12 | Manualshive

Page: 12 / 313

background image

Start here

You can solve many problems without outside assistance by following the troubleshooting procedures in this
documentation and on the World Wide Web.

This document describes the diagnostic tests that you can perform, troubleshooting procedures, and
explanations of error messages and error codes. The documentation that comes with your operating system
and software also contains troubleshooting information.

Diagnosing a problem

Before you contact IBM or an approved warranty service provider, follow these procedures in the order in
which they are presented to diagnose a problem with your blade server.

Step 1.

Return the server to the condition it was in before the problem occurred.

If any hardware, software, or firmware was changed before the problem occurred, if possible,
reverse those changes. This might include any of the following items:

• Hardware components

• Device drivers and firmware

• System software

• UEFI firmware

• System input power or network connections

Step 2.

View the light path diagnostics LEDs and event logs.

The blade server is designed for ease of diagnosis of hardware and software problems.

•

Light path diagnostics LEDs:

See “Light path diagnostics” on page 202 for information about

using light path diagnostics LEDs.

•

Event logs:

See “Event logs” on page 147 for information about notification events and

diagnosis.

•

Software or operating-system error codes:

See the documentation for the software or

operating system for information about a specific error code. See the manufacturer's website for
documentation.

Step 3.

Run IBM Dynamic System Analysis (DSA) and collect system data.

Run Dynamic System Analysis (DSA) to collect information about the hardware, firmware, software,
and operating system. Have this information available when you contact IBM or an approved
warranty service provider. For instructions for running DSA, see the

Dynamic System Analysis

Installation and User's Guide

.

To download the latest version of DSA code and the

Dynamic System Analysis Installation and

User's Guide

, go to http://www.ibm.com/support/entry/portal/docdisplay?lndocid=SERV-DSA.

«
...
10
11
12
13
14
...
»

Summary of Contents for BladeCenter HX5 1909


























































































































































































































































































































Reviews:

No comments

Related manuals for BladeCenter HX5 1909

Brand: IBM Pages: 438

Brand: IBM Pages: 180

BladeCenter JS20

Brand: IBM Pages: 132

UltraNEXUS-HD X5

Brand: Leightronix Pages: 5

Brand: EMC Pages: 34

Brand: Opengear Pages: 4

PRIMERGY TX2550 M4

Brand: Fujitsu Pages: 563

Active Fabric Manager

Brand: Dell Pages: 44

Brand: Dell Pages: 120

Brand: Dell Pages: 76

Active Fabric Manager

Brand: Dell Pages: 127

Brand: Dell Pages: 122

DR4000 Restore Manager

Brand: Dell Pages: 156

Chassis Management Controller

Brand: Dell Pages: 234

Brand: Dell Pages: 160

Brand: Dell Pages: 160

Brand: Dell Pages: 190

Brand: Dell Pages: 133

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands