Lenovo BladeCenter HX5 1909 Problem Determination And Service Manual Download Page 137

Page: 137 / 313

Step 8. Remove the CFFh expansion card, if one is installed (see “Removing a CFFh expansion card” on

page 119 for instructions).

Step 9. Locate the CIOv expansion connector (see “Blade server connectors - BladeCenter HX5” on page

12).

Step 10. Using your fingers, move the retaining clips away from the CIOv card; then, lift the card out of the

connector.

Step 11. If you are instructed to return the CIOv expansion card, follow all packaging instructions, and use

any packaging materials for shipping that are supplied to you.

Installing an I/O expansion card

The following sections describe how to install the following expansion cards:

• CFFh expansion cards, for example:

– QLogic 2-Port 10Gb Converged Network Adapter

– QLogic Ethernet and 8 GB Fibre Channel Expansion Card

– 2/4-Port Gb Ethernet Expansion Card

– 2-Port 40 Gb Infiniband Expansion Card

– Brocade 2-Port 10 Gb Ethernet Converged Network Adapter

– Broadcom 2-Port 10 Gb Ethernet Expansion Card

– Broadcom 2-Port 10 Gb Virtual Fabric Adapter

– Broadcom 4-Port 10 Gb Ethernet Expansion Card

– Emulex Virtual Fabric Adapter

– Emulex Virtual Fabric Adapter Advanced

– Emulex 10 Gb Ethernet Virtual Fabric Adapter 2

– Emulex 10 Gb Ethernet Virtual Fabric Adapter Advanced 2

– Intel 10 Gb 2-Port Ethernet Expansion Card

• CIOv expansion cards, for example:

– Ethernet Expansion Card

– QLogic 8 Gb Fibre Channel Expansion Card

– QLogic 4 Gb Fibre Channel Expansion Card

– SAS Connectivity Card

Note:

A CIOv expansion card is supported for all combinations.

The following illustration shows the cards that are supported in a blade server.

Chapter 4

Removing and replacing blade server components

121

Summary of Contents for BladeCenter HX5 1909


























































































































































































































































































































Search results

Summary of Contents for BladeCenter HX5 1909

Reviews:

Related manuals for BladeCenter HX5 1909

Brands by name

Popular brands

Lenovo BladeCenter HX5 1909, Problem Determination And Service Manual

Search results

Summary of Contents for BladeCenter HX5 1909

Reviews:

Related manuals for BladeCenter HX5 1909

Brands by name

Popular brands