Kinova Link 6 User Manual Download

Page: 264 / 296

EN UG-020 Link 6 user guide r1.0

256

Figure 213: Dimensions of the Kinova Gigabit Ethernet adapter measured in millimeters

Installing the Gigabit Ethernet adapter

The adapter installs directly to the

wrist

of Link 6.

Before you begin

Personnel:

•

Number of Workers:

Supplies

• 4 x M6-1.0-6h screws

Note:

maximum thread engagement depth: 6 mm

Note:

Torque: 7-9 N·m

• 2 x 6 mm dowels

Note:

The dowels are not used to stabilize the

end effector

; they are used to guide the

end effector onto the wrist.

•

Flange

system position: 0° and 180°

About this task

Installation of optional tools is done in a stacking fashion. That is, the Gigabit Ethernet adapter

must be fixed to the wrist before other optional tools are attached to the adapter.

Procedure

Remove the end cap from the wrist and the end cap from the adapter.

+1 514-277-3777

kinovarobotics.com

Summary of Contents for Link 6




































































































































































































































































































Search results

Summary of Contents for Link 6

Reviews:

Related manuals for Link 6

Brands by name

Popular brands

Kinova Link 6, User Manual

Search results

Summary of Contents for Link 6

Reviews:

Related manuals for Link 6

Brands by name

Popular brands