Kinova Link 6 User Manual Download Page 161

Page: 161 / 296

EN UG-020 Link 6 user guide r1.0

153

Procedure

Tap .

The

Create new custom tool

dialog launches.

Enter the information about the custom tool.
•

Name

•

Mass

•

Transform: x, y, z

in mm

•

Transform: θx, θy, θz

in °

•

Center of Mass: x, y, z

in mm

•

Center of Mass: θx, θy, θz

in °

•

Inertia Matrix: ixx, ixy, ixz, iyy, iyz, izz

in kg/m

DANGER:

Make sure the

Mass

and

Center of Mass

input for the payload correspond to

the physical mass and center of mass of the payload installed on the robot.
If the physical mass and physical center of mass of the payload does not match what is

entered in the Create new custom tool form, it could lead to erratic behavior of the robot

when it is used in Hand Guiding mode.

+1 514-277-3777

kinovarobotics.com

Summary of Contents for Link 6




































































































































































































































































































Search results

Summary of Contents for Link 6

Reviews:

Related manuals for Link 6

Brands by name

Popular brands

Kinova Link 6, User Manual

Search results

Summary of Contents for Link 6

Reviews:

Related manuals for Link 6

Brands by name

Popular brands