Kentrox RMM-1400 Configuration Manual Download Page 199 | Manualshive

Page: 199 / 246

background image

Remote RMM-1400 Version 2.0x Configuration Guide

Using Configuration Wizards: Using the initsetup Wizard

19-3

Using the initsetup Wizard

To configure the initial setup:

1. From the main prompt, access the

initsetup

wizard:

config use-wizard initsetup

The initsetup wizard screen appears:

2. Enter the desired hostname.

3. Enter the desired IP address for the device when prompted.

4. Enter the desired subnet mask length when prompted.

5. (optional) Enter the desired login account information when prompted.

In this scenario, you will configure the initial setup for Remote RMM-1400 using the
initsetup wizard. The wizard prompts you for all of the required and optional
information.



Note:

The

running-config

file is automatically saved to a

network-recovery

file when you run the initsetup wizard and apply the output to the

running-config

file. If the running configuration is lost, you can copy file

network-recovery

to file

running-config

to restore the initial system

configuration.

(Dub)>config use-wizard initsetup

---------------------
----- initsetup -----
---------------------

This wizard configures initial connectivity settings.

An asterisk (*) in a selection list denotes the default value.

Ctrl-c aborts the wizard.

NOTE:
This wizard provides only basic configuration. For additional
configuration options, consult the command reference guide.

Hostname of this device:

«
...
197
198
199
200
201
...
»

Summary of Contents for RMM-1400























































































































































































































































Reviews:

No comments

Related manuals for RMM-1400

Brand: ICP DAS USA Pages: 14

Brand: ICP DAS USA Pages: 25

Brand: ICP DAS USA Pages: 15

Brand: ICP DAS USA Pages: 8

Brand: ICP Pages: 14

Brand: Lanner Pages: 2

Brand: National Instruments Pages: 9

Brocade X6-8 Director

Brand: Broadcom Pages: 207

Brand: Juniper Pages: 190

Brand: Lanner Pages: 109

Millennium P650

Brand: Matrox Pages: 54

Brand: Paradyne Pages: 6

Brand: SeaLevel Pages: 34

640 - Pentium 4 640 3.2GHz 800MHz 2MB Socket 775 CPU

Brand: Intel Pages: 105

crown PIP Series

Brand: Harman Pages: 16

Brand: H3C Pages: 68

Brand: Paradyne Pages: 74

Brand: Microcomputer Systems Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands