manualshive.com logo in svg

Kentrox RMM-1400, Configuration Manual

Share
Download
Kentrox RMM-1400 Configuration Manual Download Page 18

Remote RMM-1400 Version 2.0x Configuration Guide

Remote RMM-1400 Product Overview: Remote RMM-1400 Hardware Configuration

1-4

Remote RMM-1400 Hardware Configuration

Figure 1-2

 shows the Remote RMM-1400 unit, which incorporates the following 

connectors and counts:

Four Ethernet ports provide for connections to your network. Ports 1 and 2 can be 
used as standard ports and can also provide 48V PoE to 802.3af-compliant 
devices.

Four serial ports provide connectivity to any asynchronous device and can be 
used as part of the Telnet to asynchronous protocol mediation application. Serial 
ports 1 and 2 operate only in RS-232 mode. Serial ports 3 and 4 operate in RS-
422 mode or RS-485 mode. Serial port 4 can serve as a console port to provide 
local asynchronous access for configuration and diagnostics from a laptop or PC.

Tx/Rx and Diversity antenna connections for the optional wireless modem.

Dual 20-60 VDC power inputs with voltage monitoring.

An auxiliary 0-60 VDC voltage monitoring input.

Figure 1-2   Remote RMM-1400

Summary of Contents for RMM-1400























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands