Kentrox RMM-1400 Configuration Manual Download Page 34

Page: 34 / 246

Remote RMM-1400 Version 2.0x Configuration Guide

Configuring Users in the CLI: Changing a User Password

3-4

Changing a User Password

To change a user password:

1. At the main prompt, change the password for user

johndoe

oldguy

config users password johndoe

The following message appears:

Please enter the new password.

2. Enter the new password:

oldguy



Note:

Passwords are case-sensitive and appear as asterisks (

) on the screen

as you type them.

The following message appears:

Please confirm the new password.

3. Re-enter the new password.

oldguy



Note:

Passwords always appear in an encrypted format within the system.
There is no way to verify that the user password has been changed.

4. Save the configuration.

In this scenario, you will change the password for an existing user.

Summary of Contents for RMM-1400






















































































































































































































































Search results

Summary of Contents for RMM-1400

Reviews:

Related manuals for RMM-1400

Brands by name

Popular brands

Kentrox RMM-1400, Configuration Manual

Search results

Summary of Contents for RMM-1400

Reviews:

Related manuals for RMM-1400

Brands by name

Popular brands