manualshive.com logo in svg

Kentrox RMM-1400, Configuration Manual

Share
Download
Kentrox RMM-1400 Configuration Manual Download Page 27

Remote RMM-1400 Version 2.0x Configuration Guide

Getting Started: Accessing the CLI Using a Remote Connection

2-7

Accessing the CLI Using a Remote Connection

To access the CLI using a remote connection:

1. Use a PC or laptop with terminal emulation software to connect to Remote RMM-

1400. For information on operating your particular terminal emulation software, 
refer to the documentation provided with the program.

2. Set up your terminal emulation software to connect using either a Telnet or an 

SSH connection.

Notes:

Individual procedures for making this connection will vary based on the 
type of software you are using.

To log into Remote RMM-1400 via SSH, you must execute command 

config remote-access ssh-sftp enable

3. Enter the IP address of the Remote RMM-1400 to which you want to connect.

4. At the login prompt, enter your user name:

janedoe

5. At the password prompt, enter your password:

mypassword

Notes:

Passwords are case-sensitive.

admin

 is the default user name and 

password

 is the default password. 

Remote RMM-1400 lets you log in only five times using the default 
password. On your sixth login, Remote RMM-1400 will prompt you to 
change the default password to a new password.

In this scenario, you will connect and log into Remote RMM-1400 remotely using 
either a Telnet or an SSH connection.

Note:

You can also connect remotely to Remote RMM-1400 using the HTTP or 
HTTPS protocols.

Summary of Contents for RMM-1400























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands