manualshive.com logo in svg

Kentrox RMM-1400, Configuration Manual

Share
Download
Kentrox RMM-1400 Configuration Manual Download Page 127

Remote RMM-1400 Version 2.0x Configuration Guide

Configuring Mediation Connections: Configuring a TCP to Asynchronous Serial Connection

14-5

The command response appears similar to the following:

5. Configure controller 

serial 2 

to connect and disconnect as 

DCD

 goes active and 

inactive:

config controller serial 2 connect mode dcd

config controller serial 2 disconnect mode dcd

6. Configure the application mode as 

destination

:

config controller serial 2 application destination

7. (optional) Verify that a connection is established:

show connections

The command response appears similar to the following:

Note:

The 

4

 that comes after the TCP port number is an internal reference 

number generated by Remote RMM-1400.

8. Save the configuration.

(Dub)>show actions tcpToSerial2
Action Name          : tcpToSerial2
Action Description   :

Event Name           : tcp40010
Event Description    :
Event Originator     : tcp 10.40.57.5:40010
Event Type           : incoming-connection

Response Name        : tcp40010ToSerial2
Response Description :
Response Responder   : tcp 10.40.57.5:40010
Response Type        : connect
Response Parameters  :
                       dest=serial 2
(Dub)>

(Dub)>show connections
tcp 10.40.57.5:40010:4 -> serial 2
(Dub)>

Summary of Contents for RMM-1400























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands