manualshive.com logo in svg

Kentrox RMM-1400, Configuration Manual

Share
Download
Kentrox RMM-1400 Configuration Manual Download Page 33

Remote RMM-1400 Version 2.0x Configuration Guide

Configuring Users in the CLI: Enabling the Strong Password Feature

3-3

Enabling the Strong Password Feature

The strong password is an optional security feature that enforces additional 
validations on new or changed user passwords. The password validations apply to 
passwords entered for local users only.

The strong password feature is disabled by default.

To enable the strong password feature:

1. At the main prompt, enable the strong password:

config users strong-password enable

2. (optional) Verify that the strong-password feature is enabled:

show users

The command response appears similar to the following:

3. Change the existing password for user 

ebh

. The following example shows the 

additional restrictions of the strong password feature.

In this scenario, you will:

Enable the strong password feature.

Change an existing user password.

(Dub)>show users
Strong Password Support: enabled

              Login Name              Profile
 1.                  bob           restricted
 2.                  ebh           restricted
 3.                 jeff               status
 4. 

tech 

management

 5.                 test           supervisor
(Dub)>

(Dub)>config users password ebh
Please enter the new password. ********
Please confirm the new password. ********
[ATHM0029] Password must contain at least one character from three of the
           following types: upper-case, lower-case, numerical, and special
           punctuation.
(Dub)>config users password ebh
Please enter the new password. *********
Please confirm the new password. *********
(Dub)>

Summary of Contents for RMM-1400























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands