manualshive.com logo in svg

Kentrox RMM-1400, Configuration Manual

Share
Download
Kentrox RMM-1400 Configuration Manual Download Page 117

Remote RMM-1400 Version 2.0x Configuration Guide

Configuring Measurements and the Measurement Table: Configuring a Measurement Table Entry for a

Temperature Sensor

13-5

10. (optional) Verify that the measurement table entry has been configured properly:

show meas-table entries ExtTemp1

The command response appears similar to the following:

11. Save the configuration.

Sample Configuration for SiteBus Temperature Sensor

The following is a sample configuration for a measurement table entry for the SiteBus 
temperature sensor used with RMB-1 and RMB-2. Adjust the sensor name, NE name, 
and other values to fit your specific implementation.

config meas-table entry TempSensor1

config meas-table entry TempSensor1 category Temp Sensor

config meas-table entry TempSensor1 description One Wire Temp 

Sensor

config meas-table entry TempSensor1 originator sitebus 

Temp/temperatureF

config meas-table entry TempSensor1 report-interval 15

config meas-table entry TempSensor1 band 20 110

config meas-table entry TempSensor1 hysteresis 2

config meas-table entry TempSensor1 maximum 150

config meas-table entry TempSensor1 minimum -10

config meas-table entry TempSensor1 ne-name Test_RMM1400

config meas-table entry TempSensor1 units degrees Fahrenheit

(Dub)>show meas-table entries ExtTemp1
Name             - ExtTemp1 (static)
State            - offline
Originator       - analog 1/4
Description      - External temperature sensor
NE Name          - sensorUnit
Category         - envAlms
Report Interval  - 0
Low-Band         - 65.
High-Band        - 80.
Hysteresis       - 0.
Max-Limit        - 130.
Min-Limit        - -30.
Units            - Degrees F

Current Value    - 76
Interval Value   - 76
Interval Minimum - 76
Interval Maximum - 76
Interval Average - 76
(Dub)>

Summary of Contents for RMM-1400























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands