manualshive.com logo in svg

Kentrox RMM-1400, Configuration Manual

Share
Download
Kentrox RMM-1400 Configuration Manual Download Page 168

Remote RMM-1400 Version 2.0x Configuration Guide

Configuring the SNMP Proxy: SNMP Proxy Configuration Information

17-4

The predefined variables that are available for use in these templates are described in 

Table 17-1 on page 17-4

.

SNMP NE

The mediation SNMP NE is a mediation event originator. The originator type is 
snmpne, and the originator instance is the name of the mediation NE. The snmpne 
contains site-specific information, and can be linked with a previously created event 
template or a point template for part of its definition.

The name of the NE is used as the NE name value for mediation alarm table entries 
and responses.

SNMP Manager

The configurable information for the SNMP manager is the port on which the SNMP 
manager listens for incoming SNMP notifications. The default port is 162.

Table 17-1   Predefined Template Variables

Variable

Description

$(point)

Contains the name of the point configured on the 
mediation SNMP NE

$(event)

Contains the name of the event configured on the 
mediation SNMP NE

$(measurement)

Contains the name of the measurement configured 
on the mediation SNMP NE

$(snmpne)

Contains the name of the mediation SNMP NE

Summary of Contents for RMM-1400























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands