manualshive.com logo in svg

Kentrox RMM-1400, Configuration Manual

Share
Download
Kentrox RMM-1400 Configuration Manual Download Page 107

Remote RMM-1400 Version 2.0x Configuration Guide

Configuring Alarm Entries in the Central Alarm Table: Configuring an Alarm Entry for a Serial Connection

Failure

12-11

4. (optional) Verify that the alarm entry has been configured properly:

show alarm-entries name SerConnFail

The command response appears similar to the following:

5. Save the configuration.

(Dub)>show alarm-entries name SerConnFail
Name             - SerConnFail
State            - normal
Current Message  -
Description      - Serial connection failure
Nagging Interval - 0
Nagging Level    - major
Trap             - enabled
Trap Priority    - disabled
Raw              - disabled
Category         -
NE Name          -
Originator       - serial 3
Alarm Actions:
 Severity    Trigger                Message
------------------------------------------------------------------
 major       conn-failed            The serial connection has fail
(Dub)>

Summary of Contents for RMM-1400























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands