manualshive.com logo in svg

Kentrox RMM-1400, Configuration Manual

Share
Download
Kentrox RMM-1400 Configuration Manual Download Page 225

Glossary-13

 Glossary

hysteresis

Hysteresis is a guard region around high and low thresholds on an analog input that 
prevents rapid generation of events when input current oscillates rapidly across the 
threshold.

I

inactivity timeout

The inactivity timeout sets the frequency (in minutes) that RX statistics will be 
checked on a link in the event that a wireless service provider does not provide lcp-
requests (keep alives) in their network, or imposes time limitations on the network 
connections. 

interface

An interface is another concept that is applied throughout the CLI. It is an entity to 
which you can route IP packets. An interface must be associated with a controller, 
which may be an underlying physical port.

IP forwarding

IP forwarding allows IP packets received on an interface to be forwarded to other 
interfaces.

IP routing table

The IP routing table is a database in a router that keeps track of paths to particular 
networks and network destinations. More specifically, it associates network 
addresses with gateway addresses.

Iptables

Iptables is the method by which IP packets are filtered or manipulated for Remote 
RMM-1400. IP packets are filtered or manipulated using three iptables: 

filter

, which 

filters IP packets, 

mangle

, which manipulates IP packets, and 

NAT

, which routes IP 

packets.

Summary of Contents for RMM-1400























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands