manualshive.com logo in svg

Kentrox RMM-1400, Configuration Manual

Share
Download
Kentrox RMM-1400 Configuration Manual Download Page 221

Glossary-9

 Glossary

discrete expansion peripheral

A discrete expansion peripheral is a component that allows the user to add additional 
discrete inputs, analog inputs, and relay outputs to Remote RMM-1400’s 
configuration. These additional I/O points are managed through Remote RMM-1400.

discrete peripheral unit

The discrete peripheral unit is a space on Remote RMM-1400 that holds the I/O 
configuration information for a discrete peripheral. Units are numbered 0 to 4, with 0 
representing the on-board discrete I/O subsystem.

domain name

Domain names are used to represent IP addresses on a network and are formatted 
as a series of alphanumeric characters separated by periods (for example, 
www.domainname.com).

DNS server

A DNS server translates alphanumeric addresses into corresponding IP addresses.

DTR signal

DTR is a control signal on an Remote RMM-1400 asynchronous RS-232 serial port.

E

encapsulation

Communications encapsulation is a method for transmitting multiple protocols within 
the same network. The frames of one type of protocol are carried within the frames of 
another. The available communications encapsulation formats for Remote RMM-1400 
are HDLC and PPP.

Summary of Contents for RMM-1400























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands