Kentrox RMM-1400 Configuration Manual Download Page 229 | Manualshive

Page: 229 / 246

background image

Glossary-17

Glossary

maximum current

The maximum current is the highest valid current allowed on a specified analog input
and the sensor value associated with that current.

maximum lease time

The maximum lease time is the maximum amount of time, in seconds, a device can
use an IP address assigned by the DHCP server.

mediation connection

Mediation connections are connections that allow the interconnection of different
protocols. The protocols on each side are terminated in the middle so that the
interconnection can occur.

minimum current

The minimum current is the lowest valid current that will be present on the specified
analog input and the sensor value associated with that current.

MRU

The MRU sets the maximum number of data bytes that can be received in a single
PPP frame on a WAN port.

MTU

The MTU sets the maximum number of data bytes that can be transmitted in a single
PPP frame on a WAN port.

«
...
227
228
229
230
231
...
»

Summary of Contents for RMM-1400























































































































































































































































Reviews:

No comments

Related manuals for RMM-1400

3CR860-95 - OfficeConnect Secure Router

Brand: 3Com Pages: 2

Brand: 3Com Pages: 26

SCSI PC Card REX-9530V

Brand: Ratoc Systems Pages: 30

Brand: Accusys Pages: 34

PG-FlexPlus AMU-912

Brand: ADC Pages: 130

Brand: Fieldbus Specialists Pages: 39

Brand: Patton electronics Pages: 12

Brand: IEI Technology Pages: 86

Lite N42B1P Series

Brand: Dahua Technology Pages: 14

Active Module Carrier VX402C-64

Brand: C&H Pages: 32

AT-8550/SP Series

Brand: Allied Telesis Pages: 114

Brand: Belkin Pages: 57

Brand: SAGEMCOM Pages: 75

InnoMedia MTA 3328-2R

Brand: VoiceLine Pages: 18

Brand: DigiTech Pages: 6

Brand: Compal Pages: 47

Brand: Acromag Pages: 35

Brand: Bailey Pages: 33

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands