manualshive.com logo in svg

Kentrox RMM-1400, Configuration Manual

The Kentrox RMM-1400 Configuration Manual is the ultimate guide to effectively set up and optimize your Kentrox RMM-1400 device. This comprehensive manual is available for free download at manualshive.com, ensuring hassle-free access to valuable instructions and insights in maximizing the potential of your Kentrox RMM-1400.

Share
Download
background image

TOC-4

Table of Contents

Chapter 14:   Configuring Mediation Connections  .................................14-1

Overview .................................................................................................................... 14-2
Secure Terminal Server Access ................................................................................. 14-3

Terminal Server User Access ......................................................................... 14-4

Configuring a TCP to Asynchronous Serial Connection  ............................................ 14-4
Configuring a Telnet to Asynchronous Serial Connection .......................................... 14-6
Configuring a SSH to Asynchronous Serial Connection  ............................................ 14-8
Configuring an Asynchronous Serial to Asynchronous Serial Connection ............... 14-10
Configuring an Asynchronous Serial to TCP Connection  ........................................ 14-13

Chapter 15:   Configuring the DHCP Server  ..........................................15-1

DHCP Server Overview  ............................................................................................. 15-2
Configuring a DHCP Server ....................................................................................... 15-4
Configuring a DHCP Server Subnet ........................................................................... 15-6
Configuring a Host on a DHCP Server ....................................................................... 15-8
Configuring BOOTP/DHCP Relay .............................................................................. 15-9
Configuring DHCP Client Support ............................................................................ 15-10

Chapter 16:   Configuring the Peripheral Management Subsystem .......16-1

Peripheral Management Subsystem Overview  .......................................................... 16-2

RMB-1 Peripheral Unit  ................................................................................... 16-2
RMB-2 Peripheral Unit  ................................................................................... 16-2

Expansion Peripheral Unit Discovery ......................................................................... 16-4
Expansion Peripheral States ...................................................................................... 16-5
Configuring Remote RMM-1400 to Manage an Expansion Peripheral  ...................... 16-7
Configuring Discrete I/O Points on an Expansion Peripheral ..................................... 16-9
Configuring Alarms for an Expansion Peripheral  ..................................................... 16-11
Configuring SNMP to Operate a Relay Output  ........................................................ 16-13
Directly Controlling a Relay Output  .......................................................................... 16-15
Configuring SiteBus Devices for an Expansion Peripheral  ...................................... 16-16
Disconnecting a Managed Expansion Peripheral  .................................................... 16-18

Chapter 17:   Configuring the SNMP Proxy ............................................17-1

SNMP Proxy Feature Overview  ................................................................................. 17-2
SNMP Proxy Configuration Information  ..................................................................... 17-3

SNMP Templates  ........................................................................................... 17-3
SNMP NE  ....................................................................................................... 17-4
SNMP Manager .............................................................................................. 17-4

Configuring a Mediation SNMP Event Template ........................................................ 17-5
Configuring a Mediation SNMP Point Template ......................................................... 17-6
Configuring a Mediation SNMP NE Template ............................................................ 17-9
Configuring a Mediation SNMP Measurement Template ......................................... 17-11

Summary of Contents for RMM-1400























































































































































































































































Reviews:

No comments

Related manuals for RMM-1400

Patton electronics Patton SmartNode 2300 Series Specification Sheet preview
Patton SmartNode 2300 Series
Brand: Patton electronics Pages: 2
Paradyne 8540 Installation Instructions Manual preview
8540
Brand: Paradyne Pages: 12
Lochinvar Armor 101 Series Instructions Manual preview
Armor 101 Series
Brand: Lochinvar Pages: 28
Lochinvar Armor 101 Series Service Manual preview
Armor 101 Series
Brand: Lochinvar Pages: 44
Automationdirect.com CLICK PLUS C2-02CPU Quick Start Manual preview
CLICK PLUS C2-02CPU
Brand: Automationdirect.com Pages: 10
Alesis QUADRAVERB Service Manual preview
QUADRAVERB
Brand: Alesis Pages: 46
RuggedCom RUGGEDSWITCH RS900G Hardware Installation Manual preview
RUGGEDSWITCH RS900G
Brand: RuggedCom Pages: 23
Commell CMB-673 Installation Manual preview
CMB-673
Brand: Commell Pages: 9
ZyXEL Communications P-336M Quick Start Manual preview
P-336M
Brand: ZyXEL Communications Pages: 125
C&T Solution RCO-3000 Series User Manual preview
RCO-3000 Series
Brand: C&T Solution Pages: 96
TRENDnet TEW-733GR User Manual preview
TEW-733GR
Brand: TRENDnet Pages: 62
Dahua NVR41-4KS2 Series User Manual preview
NVR41-4KS2 Series
Brand: Dahua Pages: 452
Cyclades AlterPath Manager 2500 Installation, Configuration And User Manual preview
AlterPath Manager 2500
Brand: Cyclades Pages: 368
Alcatel-Lucent 9364 Installation And Commissioning Manual preview
9364
Brand: Alcatel-Lucent Pages: 60
ADDON ARM8100 Quick Installation Manual preview
ARM8100
Brand: ADDON Pages: 4
2N Telekomunikace ATEUS STARGATE User Manual preview
ATEUS STARGATE
Brand: 2N Telekomunikace Pages: 67
UNICOM DynaGST/2402G GEP-33224T-1 User Manual preview
DynaGST/2402G GEP-33224T-1
Brand: UNICOM Pages: 17
Echelon i.LON SmartServer Hardware Manual preview
i.LON SmartServer
Brand: Echelon Pages: 34

Brands by name

Popular brands

Load more brands