manualshive.com logo in svg

Kentrox RMM-1400, Configuration Manual

Share
Download
Kentrox RMM-1400 Configuration Manual Download Page 146

Remote RMM-1400 Version 2.0x Configuration Guide

Configuring the DHCP Server: Configuring DHCP Client Support

15-10

Configuring DHCP Client Support

To enable DHCP client support and configure the retry-timeout interval:

1. Enable DHCP client support:

config interface bridge switch ip dhcp enable

2. Configure the DHCP retry-timeout value as 10 minutes:

config interface bridge switch ip dhcp retry-timeout 10

3. (optional) Verify that the DHCP client settings have been configured properly:

show interface bridge switch

The command response appears similar to the following:

Note:

The DHCP-related statements (shown below in boldface type) do not 
appear unless DHCP client support is enabled.

4. Save the configuration.

In this scenario, you will enable DHCP client support and configure a ten-minute 
interval for Remote RMM-1400 to retry contacting the DHCP server.

Note:

DHCP client support cannot be enabled on the bridge group 

switch

 if a 

static IP address has already been configured. You must remove the static 
IP address before enabling DHCP client support.

(Dub)>show interface bridge switch
bridge switch system-name=br_switch
            status=enabled link-state=up
            address=10.44.57.5/16
            dhcp-status=enabled dhcp-state=bound
                dhcp-retry-timeout=10
                dhcp-address=10.44.7.8/16
                dhcp-lease-acquired=Fri Sep 17 13:57:37 EST 2010
                dhcp-lease-expires=Sun Sep 19 13:57:37 EST 2010
                dhcp-routers=10.44.0.1 dhcp-server-id=10.25.2.102
        Stats:    Bytes    Packets     Errors    Dropped    Overrun    Framing
          Rx    2348892      12929          0          0          0          0
          Tx    2050152      11687          0          0          0          0

    ethernet 4
        Stats:    Bytes    Packets     Errors    Dropped    Overrun    Framing
          Rx    2587084      12964          0          0          0          0
          Tx    2618834      19175          0          0          0          0

(Dub)>

Summary of Contents for RMM-1400























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands