Kentrox RMM-1400 Configuration Manual Download Page 82

Page: 82 / 246

Remote RMM-1400 Version 2.0x Configuration Guide

Configuring Technician Laptop Access for Remote RMM-1400: Configuration Overview

10-2

Configuration Overview

Figure 10-1

displays what happens when a technician’s laptop accesses the network

by connecting to Remote RMM-1400.

Figure 10-1 Technician Laptop Access via Remote RMM-1400

IP Network

Server

Technician Laptop

IPTables

Remote RMM-1400

64.152.3.27

DHCP Server

10.10.10.12 (Private Address)

The DHCP Server
assigns a private IP
address to the
technician laptop.

(184.155.22.36)

(Public Address)

IPTables rules allow laptops
on the private network to
send packets to the WAN with
Remote RMM-1400’s public address.

Summary of Contents for RMM-1400






















































































































































































































































Search results

Summary of Contents for RMM-1400

Reviews:

Brands by name

Popular brands

Kentrox RMM-1400, Configuration Manual

Search results

Summary of Contents for RMM-1400

Reviews:

Brands by name

Popular brands