Kentrox RMM-1400 Configuration Manual Download Page 140

Page: 140 / 246

Remote RMM-1400 Version 2.0x Configuration Guide

Configuring the DHCP Server: Configuring a DHCP Server

15-4

Configuring a DHCP Server

To configure the DHCP server settings:

1. At the main prompt, enable the DHCP authority mode:

config dhcp-server authority

2. Enable the DHCP broadcast mode:

config dhcp-server broadcast

3. Configure the DHCP server to run on interface

bridge switch

config dhcp-server interface bridge switch

4. Configure the DHCP server subnet with IP address

234.55.83.0

and subnet

mask

255.255.0.0

config dhcp-server subnet 234.55.83.0 255.255.0.0



Note:

Up to 25 subnets are configurable on the DHCP server. For information on
further DHCP server subnet configurations, refer to section

Configuring a

DHCP Server Subnet on page 15-6

In this scenario, you will:



Enable

DHCP authority mode



Enable

DHCP broadcast mode



Configure the

DHCP server

to use a configuration file



Configure the DHCP server to run on the bridge interface



Configure the DHCP server subnet with an IP address and subnet mask.

Summary of Contents for RMM-1400






















































































































































































































































Search results

Summary of Contents for RMM-1400

Reviews:

Brands by name

Popular brands

Kentrox RMM-1400, Configuration Manual

Search results

Summary of Contents for RMM-1400

Reviews:

Brands by name

Popular brands