Kentrox RMM-1400 Configuration Manual Download Page 126

Page: 126 / 246

Remote RMM-1400 Version 2.0x Configuration Guide

Configuring Mediation Connections: Configuring a TCP to Asynchronous Serial Connection

14-4

Terminal Server User Access

A built-in user profile called

restricted

is available for users, which allows terminal

server access but no CLI or FTP access. At the CLI, a user with the

restricted

profile will only be able to log out; no files will be available for retrieval via FTP.

Configuring a TCP to Asynchronous Serial Connection

To configure a TCP connection to an asynchronous connection:

1. Configure event

tcp40010

with originator

tcp

10.40.57.5:40010

and event type

incoming-connection

config event tcp40010 content tcp 10.40.57.5:40010 incoming-

connection



Note:

The TCP originator IP address is optional if it is the same as the Remote
RMM-1400 bridge switch interface IP address.

2. Configure response

tcp40010ToSerial2

with responder

tcp

10.40.57.5:40010

and response type

dest

serial 2

config response tcp40010ToSerial2 content tcp 10.40.57.5:40010

connect dest serial 2

3. Configure action

tcpToSerial2

with event

tcp40010

and response

tcp40010ToSerial2

config action tcpToSerial2 event tcp40010 response

tcp40010ToSerial2

4. (optional) Verify that the TCP to asynchronous connection has been configured

properly:

show actions tcpToSerial2

In this scenario, you will configure a mediation connection between a TCP port and
an asynchronous serial controller. You will set up an action, event, and response
that cause the TCP port and controller to connect.

Summary of Contents for RMM-1400






















































































































































































































































Search results

Summary of Contents for RMM-1400

Reviews:

Brands by name

Popular brands

Kentrox RMM-1400, Configuration Manual

Search results

Summary of Contents for RMM-1400

Reviews:

Brands by name

Popular brands