manualshive.com logo in svg

Kentrox RMM-1400, Configuration Manual

Share
Download
Kentrox RMM-1400 Configuration Manual Download Page 32

Remote RMM-1400 Version 2.0x Configuration Guide

Configuring Users in the CLI: Adding a New User

3-2

Adding a New User

To add a new user:

1. At the main prompt, add a new user with user name 

johndoe

 and assign profile 

status

:

config users add johndoe status

2. At the password prompt, enter the new password. Note that the characters that 

you enter do not display, but appear as asterisks:

**********

3. When prompted to confirm, enter the same password. Again, the characters that 

you enter appear as asterisks:

**********

Notes:

User names and passwords are case-sensitive.

Available profiles are 

status

, 

management

, 

supervisor

, and

 

restricted

. For more information on these profiles, refer to the 

Remote 

RMM-1400 Command Reference Guide

.

4. (optional) Verify that the new user has been added properly:

show users

The command response appears similar to the following:

5. Save the configuration.

In this scenario, you will add a new user.

(Dub)>show users
              Login Name              Profile
 1.              janedoe           supervisor
 2.              johndoe               status
 3.                 test           supervisor
(Dub)>

Summary of Contents for RMM-1400























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands