Kentrox RMM-1400 Configuration Manual Download Page 52

Page: 52 / 246

Remote RMM-1400 Version 2.0x Configuration Guide

Configuring Network Setup Parameters: Configuring SNMP

5-10

Configuring SNMP



Note:

The following

management information base

s (MIBs) are available for Remote

RMM-1400:



aiiDefs.mib



aiMediationV2.mib



aiPeriphDiscrete.mib



aiPeripheral.mib



aiSysCfg.mib



aiSysCfgConfig.mib



aiSystem.mib



aiSystemInv.mib



aiRosetta.mib



ktxMeasurement.mib

To access the available MIBs for Remote RMM-1400, go to:

http://www3.kentrox.com/Support/Documentation-Library.aspx

To configure SNMP:

1. At the main prompt, configure an SNMP version 1 community string named

newadministrator

and assign read-only access to objects in the MIB:

config snmp community public v1 readonly

In this scenario, you will:



Configure an SNMP version 1

community string



Configure an

SNMP management station



Configure an SNMP manager for version 2 inform requests



Enable authentication

trap

transfer



Enable the

SNMP trap queue



Configure the priority level on a trap OID



Note:

This scenario applies only when an

SNMP management system

is used to

manage Remote RMM-1400.

Summary of Contents for RMM-1400






















































































































































































































































Search results

Summary of Contents for RMM-1400

Reviews:

Brands by name

Popular brands

Kentrox RMM-1400, Configuration Manual

Search results

Summary of Contents for RMM-1400

Reviews:

Brands by name

Popular brands