manualshive.com logo in svg

Kentrox RMM-1400, Configuration Manual

Share
Download
Kentrox RMM-1400 Configuration Manual Download Page 240

Glossary-28

Glossary

V

Varbind

In an SNMP message, a varbind consists of a sequence of two fields: an Object ID 
and the value for/from that Object ID.

VLAN

The term VLAN is specified by IEEE 802.1Q. It defines a method of differentiating 
traffic on a LAN by tagging the Ethernet frames. By extension, VLAN is used to mean 
the traffic separated by Ethernet frame tagging or similar mechanisms.

VPN client

The VPN client is the device that requests for a VPN session to be established on the 
VPN network.

VPN server

The VPN server is a device that provides a VPN session to clients on the VPN 
network.

W

WAN

Wide Area Network (WAN) is a computer network that covers a broad area (i.e., any 
network whose communications links cross metropolitan, regional, or national 
boundaries).

Summary of Contents for RMM-1400























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands