manualshive.com logo in svg

Kentrox RMM-1400, Configuration Manual

Share
Download
Kentrox RMM-1400 Configuration Manual Download Page 154

Remote RMM-1400 Version 2.0x Configuration Guide

Configuring the Peripheral Management Subsystem: Configuring Remote RMM-1400 to Manage an 
Expansion Peripheral

16-8

3. (optional) Verify that the expansion peripheral has been configured properly:

show peripherals unit 1

The output will look similar to the following:

Note:

The output above shows the expansion peripheral in online mode, which 
indicates that the peripheral is fully operational. Remote RMM-1400 has 
established a management connection to it and it is fully functioning as 
part of Remote RMM-1400. For more information on management states, 
refer to section 

Expansion Peripheral States on page 16-5

.

4. Save the configuration.

(Dub) show>peripherals unit 1
Unit number: 1
Description: Unit manages RMB1-0E68FD
Type: rmb-1
Admin state: Managed

Name: RMB1-0E68FD
IP address: 0.0.0.0
Oper state: Online
Manager name: RMM
Manager IP address: 10.39.90.2
Type: rmb-1
Model: B684-00.A:0
Firmware version: 1.00
Firmware build date: Jan 11 2010 09:24:04
Firmware build ID: 071
Serial number: 0000000001
Manufacture date: 12/18/09
Stage2 bootloader version: 1.00
Stage2 bootloader build date: 11/05/09
MAC address: 00:40:72:0E:68:FD
Chassis serial number: 0000000001
Chassis slot number: 0
Chassis model: B684-0
Chassis manufacture date: 12/18/09
Chassis MAC address: 00:40:72:0E:68:FD
(Dub) show>

Summary of Contents for RMM-1400























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands