Kentrox RMM-1400 Configuration Manual Download Page 144

Page: 144 / 246

Remote RMM-1400 Version 2.0x Configuration Guide

Configuring the DHCP Server: Configuring a Host on a DHCP Server

15-8

Configuring a Host on a DHCP Server

To configure a host on a DHCP server:

1. Configure host

firstHostConfig

with hardware address

12:e3:a2:45:c5:b3

config dhcp-server host firstHostConfig hardware-address

12:e3:a2:45:c5:b3

2. Configure host

firstHostConfig

with IP address

234.55.83.4

config dhcp-server host firstHostConfig ip address 234.55.83.4



Note:

The host IP address must be within one of the subnetworks being served
by the DHCP server. For more information, refer to section

Configuring a

DHCP Server Subnet on page 15-6

3. (optional) Verify that the DHCP server has been configured properly:

show dhcp-server

The command response appears similar to the following:

4. Save the configuration.

In this scenario, you will:



Configure a

DHCP server host



Configure a host hardware address



Configure a host IP address.

(Dub)>show dhcp-server
Admin State:    disabled
Broadcast:      enabled
Authority:      enabled
Config file:
Note: User specified configuration files will override configured
      DHCP server settings.
Interfaces:
bridge switch

Subnets:
234.55.0.0/16 range=234.55.83.2/234.55.83.30 router=234.55.83.1
  default-lease=36000 max-lease=40000
  DNS:
   10.51.2.67

Hosts:
firstHostConfig MAC=12:E3:A2:45:C5:B3 IP=234.55.83.4
(Dub)>

Summary of Contents for RMM-1400






















































































































































































































































Search results

Summary of Contents for RMM-1400

Reviews:

Related manuals for RMM-1400

Brands by name

Popular brands

Kentrox RMM-1400, Configuration Manual

Search results

Summary of Contents for RMM-1400

Reviews:

Related manuals for RMM-1400

Brands by name

Popular brands