Kentrox RMM-1400 Configuration Manual Download Page 110

Page: 110 / 246

Remote RMM-1400 Version 2.0x Configuration Guide

Configuring Alarm Entries in the Central Alarm Table: Configuring an Alarm Entry for a Telnet Connection
that Comes Up

12-14

Configuring an Alarm Entry for a Telnet Connection that
Comes Up

To configure the Telnet connection up alarm entry:

1. At the main prompt, configure description

Telnet connection up

config alarm-entry TelnetConnUp description Telnet connection up

2. Enable SNMP trap alarm protocol support:

config alarm-entry TelnetConnUp trap enable

3. Configure an event for alarm entry

TelnetConnUp

with the following settings:



Event originator

telnet 192.168.0.4:6001



Event trigger

conn-up



Event severity level

normal



Alarm event message

Telnet connection now up

config alarm-entry TelnetConnUp event telnet 192.168.0.4:6001

conn-up normal Telnet connection now up

Tip:

This same scenario can be followed to configure a connection up alarm entry for
SSH. Simply substitute SSH for Telnet.

In this scenario, you will:



Configure an alarm entry description



Configure SNMP alarm protocol support



Configure an alarm action that signals that a Telnet connection has come up.

Summary of Contents for RMM-1400






















































































































































































































































Search results

Summary of Contents for RMM-1400

Reviews:

Brands by name

Popular brands

Kentrox RMM-1400, Configuration Manual

Search results

Summary of Contents for RMM-1400

Reviews:

Brands by name

Popular brands