Kentrox RMM-1400 Configuration Manual Download Page 118

Page: 118 / 246

Remote RMM-1400 Version 2.0x Configuration Guide

Configuring Measurements and the Measurement Table: Configuring an Alarm Entry for a Measurement

13-6

Configuring an Alarm Entry for a Measurement

To configure the measurement alarm entry:

1. At the main prompt, configure alarm entry

ExtTemp

with description

External

temperature alarm

config alarm-entry ExtTemp description External temperature alarm

2. Configure category name

envAlms

config alarm-entry ExtTemp category envAlms

3. Configure network element name

sensorUnit

config alarm-entry ExtTemp ne-name sensorUnit

4. Enable SNMP trap alarm protocol support with priority

normal

config alarm-entry ExtTemp trap enable

config alarm-entry ExtTemp trap priority normal

5. Configure an event for alarm entry

ExtTemp

with the following settings:



Event originator

measurement ExtTemp1



Event trigger

high



Event severity level

major



Alarm event message

$(value)



Note:

Keyword

$(value)

is replaced with the current measurement value.

config alarm-entry ExtTemp event measurement ExtTemp1 high major

$(value)

In this scenario, you will:



Configure an alarm entry description and category



Configure the network element name associated with this alarm entry



Configure SNMP trap alarm protocol support



Configure different alarm actions that occur when a measurement is normal,
low, high, falls below the measurable range, or rises above the measurable
range

Summary of Contents for RMM-1400






















































































































































































































































Search results

Summary of Contents for RMM-1400

Reviews:

Related manuals for RMM-1400

Brands by name

Popular brands

Kentrox RMM-1400, Configuration Manual

Search results

Summary of Contents for RMM-1400

Reviews:

Related manuals for RMM-1400

Brands by name

Popular brands