Home
/
Kentrox
/
RMM-1400
/
Configuration Manual

Kentrox RMM-1400, Configuration Manual

Share

Page: 141 / 246

Kentrox RMM-1400 Configuration Manual Download Page 141

Remote RMM-1400 Version 2.0x Configuration Guide

Configuring the DHCP Server: Configuring a DHCP Server

15-5

5. (optional) Verify that the DHCP server has been configured properly:

show dhcp-server

The command response appears similar to the following:

6. Save the configuration.

Tip:

Remote RMM-1400 lets you specify a DHCP server configuration file. This file
overrides any DHCP server settings configured in the Remote RMM-1400 CLI.
If you do not specify the correct DHCP server configuration file, Remote RMM-
1400 generates an error. The following command specifies file

dhcpconfig1.txt

as the DHCP configuration file:

config dhcp-server config-file dhcpconfig1.txt

The DHCP server configuration file must exist in Remote RMM-1400 directory

/config/dhcp

before you can specify it as the configuration file in the Remote

RMM-1400 CLI. For information about creating a DHCP server configuration
file, refer to the dhcpd.conf man page.

(Dub)>show dhcp-server
Admin State:    disabled
Broadcast:      enabled
Authority:      enabled
Config file:
Note: User specified configuration files will override configured
      DHCP server settings.
Interfaces:
bridge switch

Subnets:
234.55.0.0/16 range=0.0.0.0/0.0.0.0 router=0.0.0.0
default-lease=3600 max-lease=28800
DNS:

Hosts:
(Dub)>

«
...
139
140
141
142
143
...
»

Summary of Contents for RMM-1400























































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands