manualshive.com logo in svg

Kentrox RMM-1400, Configuration Manual

Share
Download
Kentrox RMM-1400 Configuration Manual Download Page 41

Remote RMM-1400 Version 2.0x Configuration Guide

Saving and Applying Configurations: Restoring Basic Network Settings

4-5

Restoring Basic Network Settings

To restore the basic network settings, copy the network recovery file to the running 
configuration:

copy network-recovery running-config

You can also restore the network settings from the Remote Web interface as follows:

1. Click the 

Configuration

 button on the left side of the screen or 

Configuration

 

from the Main Menu. 

2. In the 

Restore

 section of the screen, click 

From backup file:

, then

 

select

 

network-recovery 

from the drop-down menu.

3. Click the 

Restore 

link. The screen refreshes and confirms your selection.

See 

Accessing the Web Interface on page 2-8

 for details.

In this scenario, you will restore Remote RMM-1400’s basic network settings. 
These settings are entered in the initsetup wizard. The 

running-config

 file is now 

automatically saved to a 

network-recovery

 file when the you run the initsetup 

wizard and apply the output to the 

running-config

 file. If the running configuration 

is lost, users can save file 

network-recovery

 to file 

running-config

 to restore 

the initial system configuration.

Note:

For more information on the initsetup wizard, refer to 

Using the initsetup 

Wizard on page 19-3

.

Summary of Contents for RMM-1400























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands